[MW:34866] Presentation for WPS ,PQR AND WPQ as per ASME Sec IX in power point

Dear Experts.

       If anyone having presentation of WPS,PQR and WPQ  as per ASME  SEC.IX  in power point then please share .

Regards

Sanjay 

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CALkBf%2Bv86scDvHMsErUYtjP2jBz9401YHHviD8zgO7irSaABFA%40mail.gmail.com.

[MW:34866] Nase requiremenr

can anyone suggest what are the requirement  for cosumable for nace applicable fabrication?

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/f7acf029-77a6-4ba3-947c-cb1381c146b0n%40googlegroups.com.

Re: [MW:34865] PQR Thk clarification required for SS ( Dissimilar Fabrication weld Joint )

Your groove weld is 22mm, so you can select PQR base metal thik 11mm and above.

Regards 

D.V.Reddy.

On Wed, 10 Apr 2024, 7:55 pm PARAI Reaction Channel, <saravanshyla@gmail.com> wrote:

Dear Sirs,

I need to clarify the following weld joint very urgently.

As per the below snapshot sketch,

in order to weld the Lifting Lug (3) 45mm and the support plate (4) 22mm for the combined Groove and Fillet weld joint configuration given in the sketch, 

that is for the P No.8 materials ( A240-Gr.304L ) as per ASME Sec IX requirements,

When I select the PQR base metal Thk to weld this dissimilar fabrication joint of base metal thickness 22mm & 45mm, 

should I consider the maximum fabrication base metal thk of 45mm Lifting Lug too? Or I just consider the fabrication base metal of the support plate 22mm only.

Can I select the PQR base metal thk of 11mm only ?

Please advice.

Regards,

Saravanan Sornam,

ANSAN-Si,

S.Korea.

0082-10-9071-9680

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CALV1rkLK%2BR%3Djsp8b-JAceDNSCHCQBovv0j8Ma0Uu0NxA5%3DiizQ%40mail.gmail.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAEabyK%3DqGCzcpFDBMhUXz1yc1hjv3yLMG_9wkgq-6euMF7A6WA%40mail.gmail.com.

[MW:34864] Set in and set on weld joints OD restrictions for welders.

Dear welding experts,

Let me know set in and set on weld joints OD restrictions for welders.

Both joints consider as butt joints or not.

Please give code reference ASME Sec IX.

Thank you,

D.V.Reddy.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAEabyKkfKOmm2Jtf9-20nL0G1M2G%2B_6Nkg5pTUDr1RpD4BhfNg%40mail.gmail.com.

[MW:34862] Power point presentation _ PMI & Codes & standards _ urgent

Dear Well wishers , 

can anybody  send the powerpoint presentation of  Hardness, PMI and Codes  &  standards for reference ....please

If any other powerpoint presentation is available , please share it with me to get more knowledge.

With Warm Regards,

S.TAMIZH SELVAN,

Mobile: +91-9597370860 ( India )

          

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CABHCQ-Gn5dA5beH6p9hGHpLoBopRnb%2BNtfC9kn4OiyZrotP1kg%40mail.gmail.com.

Re: [MW:34861] WPS for overlay (QW 403.20)

Thank you!

I don't understand how QW403-20 is different from QW403-11?

What does it mean for QW 403.20 to determine the chemical composition of the weld metal overlay specified in the WPS? Can you please explain clearly here? Is it possible to determine the chemical composition of the weld overlay in PQR after the overlay is completed? What is the method to determine it?

Thank you for your contribution!

Best ragards!

....................................

DƯƠNG VINH QUANG - WELDING ENGINEER

● Welding Team - Central Engineering - NSRP

● Email:  duongvinhquanga13@gmail.com

● Phone: +84 (0) 964 801 295

On Wed, 10 Apr 2024 at 14:13, 'james gerald' via Materials & Welding <materials-welding@googlegroups.com> wrote:

This clause is pertaining to substrate Base material (P.No.) over which weld overlay is Done.

Normally the Client specification or the mandate code will specify the chemistry of the overlay and at what depth from the Fusion line.

An example of Refinery code giving chemistry requirement in API RP-582 below.

Hope now you can read and understand.

Thanks & Regards

J.Gerald Jayakumar

0091-8838619635

On Wednesday, 10 April, 2024 at 10:47:15 am IST, Dương Vinh Quang <duongvinhquanga13@gmail.com> wrote:

Dear experts,

I'm writing WPS for overlay following ASME IX, but I have a concern about section QW 403.20 " If the chemical composition of the weld metal overlay is specified in the WPS, a change in the P-Number listed in Table QW/QB-422 to another P-Number or unlisted base metal, or a change in Group Number for P-No. 10 or P-No. 11 base metals.

If the chemical composition of the weld metal overlay is not specified in the WPS, qualification on P-No. 5A or any lower P-Number base metal also qualifies for weld metal overlay on all lower P-Number base metals".

I hope that you can help me to explain about this paragraph. If possible, please give me a specifc example. Thank you all!

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/40c92c78-d955-4db9-bb71-14be4a366225n%40googlegroups.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/1538150546.4493684.1712732061871%40mail.yahoo.com.

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAOdNLKhCQqgXCxm10qgysXuYjmx%3DpGjf_wapcfkk6FuwTqk0EA%40mail.gmail.com.

Re: [MW:34860] WPS for overlay (QW 403.20)

This clause is pertaining to substrate Base material (P.No.) over which weld overlay is Done.

Normally the Client specification or the mandate code will specify the chemistry of the overlay and at what depth from the Fusion line.

An example of Refinery code giving chemistry requirement in API RP-582 below.

Hope now you can read and understand.

Thanks & Regards

J.Gerald Jayakumar

0091-8838619635

On Wednesday, 10 April, 2024 at 10:47:15 am IST, Dương Vinh Quang <duongvinhquanga13@gmail.com> wrote:

Dear experts,

I'm writing WPS for overlay following ASME IX, but I have a concern about section QW 403.20 " If the chemical composition of the weld metal overlay is specified in the WPS, a change in the P-Number listed in Table QW/QB-422 to another P-Number or unlisted base metal, or a change in Group Number for P-No. 10 or P-No. 11 base metals.

If the chemical composition of the weld metal overlay is not specified in the WPS, qualification on P-No. 5A or any lower P-Number base metal also qualifies for weld metal overlay on all lower P-Number base metals".

I hope that you can help me to explain about this paragraph. If possible, please give me a specifc example. Thank you all!

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/40c92c78-d955-4db9-bb71-14be4a366225n%40googlegroups.com.

[MW:34859] WPS for overlay (QW 403.20)

Dear experts,

I'm writing WPS for overlay following ASME IX, but I have a concern about section QW 403.20 " If the chemical composition of the weld metal overlay is specified in the WPS, a change in the P-Number listed in Table QW/QB-422 to another P-Number or unlisted base metal, or a change in Group Number for P-No. 10 or P-No. 11 base metals.

If the chemical composition of the weld metal overlay is not specified in the WPS, qualification on P-No. 5A or any lower P-Number base metal also qualifies for weld metal overlay on all lower P-Number base metals".

I hope that you can help me to explain about this paragraph. If possible, please give me a specifc example. Thank you all!

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/40c92c78-d955-4db9-bb71-14be4a366225n%40googlegroups.com.

[MW:34857] Need 316L-UG WPS with PQR if available Using Er310L and E310L

Hi experts,

Please share

 316L-UG WPS with PQR  if available Using Er310L and E310L

Regards 

Sreekumar 

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/CAGKmK8RdSPuGHMJmesN3-b0E%3D%2B%2BdxKAkb%3D0LwZBWBdZRy1CwxQ%40mail.gmail.com.

[MW:34855] Numerical on Impact test

Two coupons are to be welded having thickness 20mm and 40mm. Please explain with sketch the location of impact specimen for each case as per UG-84 of ASME Div VIIII DIv 1.

Kindly solve this problem 

--
https://materials-welding.blogspot.com/
https://www.linkedin.com/groups/122787
---
You received this message because you are subscribed to the Google Groups "Materials & Welding" group.
To unsubscribe from this group and stop receiving emails from it, send an email to materials-welding+unsubscribe@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/materials-welding/345d23fd-d62e-441f-82b9-e013094e7886n%40googlegroups.com.